Duct Joints and Other Joint Equipment

Straight Connector

Microduct snap-in connectors for quick and easy splicing of microducts. The body is transparent for easy fault location during installation. The connector is available for 5/3.5mm and 3/2mm ducts.

Straight Connector for Thick Walled Ducts

Microduct snap-in connectors for quick and easy splicing of microducts. The connector is available for 7/3.5mm ducts and can be direct buried. It is equipped with safety locks for unaccidental opening during installation.

Gas Block Connector 5 mm

Gas block microduct snap-in connectors is normally used between indoor and outdoor environments to prevent air flow that may result in condensed water getting into in ducts. After cable installation, the connector can be gas sealed by turning a ring on the body.

Gas Block Connector 7 mm

Gas block microduct snap-in connectors normally used between indoor and outdoor environments to prevent air flow that may result in condensed water getting into in ducts. After cable installation, the connector can be gas sealed by Pushing the connector ends together. This version is intended for 7mm thick walled ducts.

End Stop Connector

Microduct snap-in end stop connectors for permanent or temporarily sealing of unused microducts to prevent water and dust from getting into the duct.

End Stop Connector for Thick Walled Ducts

Microduct snap-in, end-stop connectors for permanent or temporarily sealing of unused microducts to prevent water and dust getting into the duct. This type is intended for thick walled ducts.

Divisible Seals

The divisible seals for microducts provide a gas and watertight seal for open duct ends installed with air blown fiber. The seals are designed to be installed after the fiber or cable has been blown in to the microduct.

Duct Joint Closure – Heat Shrink

A series of straight duct closures for maximum protection of duct joints for direct buried applications. Heat shrink technology is used for maximum protection. The closure is available in five different sizes and includes microduct snap-in connectors for 1 to 24 microducts.

Duct Joint Closure – Cold Seal

A series of straight duct closures for quick and easy installation without the need for heat. The closure is available in several sizes. Microduct snap-in connectors are not included.

Duct Branch Closure – Compact

The closure is intended for fast and easy branching of direct buried microduct assemblies for air-blown fiber. The typical application is to branch out 1 to 4 drop ducts to connect single family units from a main duct assembly. The closure is intended for mounting directly into the ground or in manholes, but can also be installed above ground.

Duct Branch Closure – Large

Branch joint closure suitable for multiducts in direct buried applications. It can be used for a large number of duct branches. The box has alternative entrances, allowing a large number of possible joint combinations, as well as mid-span access.

Duct Branch Closure – Gel

Easy-to-use fast to install closure, intended for Hexatronic’s Aerial Air Blown Fiber System, and for underground branching of ducts. The closure uses “gel-seal” technology for quick and safe installation.

Duct Joint and Branch Kit

Flexible kit including materials and tools for jointing, branching and mid-span of microducts/multiducts. A vulcanizing cloth is used for sealing, and strong and flexible PVC tape provides mechanical protection. Microduct snap-in connectors are not included. NDE 451 40/2 is a kit without tools.

End Caps

Rubber covers used for temporarily seal of unused multiducts to avoid water and dust from getting into the ducts. The caps are available in several versions for different types of ducts.

Anchoring Clamp

Designed for ducts with a Fiber Reinforced Plastic (FRP) messenger figure-8 shaped duct assembly. The 701 can also be mounted directly on aerial drop ducts.

Suspension Clamp

Designed for ducts with a Fiber Reinforced Plastic (FRP) messenger figure-8 shaped duct assembly.

Hook for Suspension Clamp

This hook is designed for the NSF 151 502 suspension clamp and enables a secure fastening of the clamp when mounted on wooden poles.

Universal Pole Bracket

Designed for securing cable or ducts on wooden, concrete or metallic poles.